Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADILON D 40EP25ZW 7037 BL - PA610 - RadiciGroup High Performance Polymers

Check here, which other Radilon D datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

PA610 flexible, high viscosity extrusion grade. Toughened and plasticized. Heat stabilized. Blue colour.

Suitable for extrusion of pipes, profiles and cable jackets. Good impact resistance also at low temperatures. This grade is partially renewably-sourced (64% of base polymer by weight).

Processing/Physical Characteristics	dry / cond	Unit	Test Standard
ISO Data
Molding shrinkage, parallel	1.6 / *	%	ISO 294-4, 2577
Molding shrinkage, normal	1.6 / *	%	ISO 294-4, 2577

Mechanical properties	dry / cond	Unit	Test Standard
ISO Data
Tensile Modulus	550 / 380	MPa	ISO 527
Stress at 50% strain	28 / 24	MPa	ISO 527
Strain at break	>50 / >50	%	ISO 527
Charpy notched impact strength, +23°C	110 / 120	kJ/m²	ISO 179/1eA
Charpy notched impact strength, -30°C	55 / -	kJ/m²	ISO 179/1eA

Thermal properties	dry / cond	Unit	Test Standard
ISO Data
Melting temperature, 10°C/min	218 / *	°C	ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa	50 / *	°C	ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa	100 / *	°C	ISO 75-1/-2

Electrical properties	dry / cond	Unit	Test Standard
ISO Data
Volume resistivity	1E13 / 1E11	Ohm*m	IEC 62631-3-1
Surface resistivity	* / 1E10	Ohm	IEC 62631-3-2

Other properties	dry / cond	Unit	Test Standard
Water absorption	2 / *	%	Sim. to ISO 62
Humidity absorption	0.9 / *	%	Sim. to ISO 62
Density	1050 / -	kg/m³	ISO 1183
Biobased content	60	%	-

Diagrams

Characteristics

Processing

Injection Molding, Pipe/Tube Extrusion, Profile Extrusion, Wire/Cable Extrusion

Delivery form

Granules

Additives

Plasticizer

Special Characteristics

High impact or impact modified, Heat stabilized or stable to heat

Certifications

Contains renewable resources

Regional Availability

North America, Europe, Asia Pacific, South and Central America, Near East/Africa

Other text information

Injection molding

The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.10%. Typical conditions with a desiccant drier: temperature 80 ° C, dew point -20 ° C or below, time 2-4 h or more. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters

Melt Temperature	Mold Temperature	Injection Speed
230 - 260°C	70 - 80°C	medium

Extrusion Temperature
240 - 290°C

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.